Las Vegas & Henderson, NV · Mon–Fri 8 AM–7 PM · Sat–Sun 8 AM–4 PM (702) 707-5107

LG WashTower · WSEX200 series

LG WSEX200HNA WashTower: error codes, settings and repair

The LG WSEX200HNA and 1 related model share LG's WSEX200 WashTower documentation. This page lists what LG's owner's manual and service manual for this series document: 66 error codes and how to turn the control lock off — with the manual page for each fact — plus the safe checks you can do and when to book a technician in Las Vegas or Henderson.

Based on LG service documentation · Reviewed by LG Appliances Repair Service technicians

Models in this series

LG's manuals for this series cover these models. Your model number is on the rating label — where to find it.

  • WSEX200HNA
  • WSGX201HNA

LG WSEX200HNA error codes

These 66 error codes and 5 status messages appear in LG's documentation for this series. The page reference points to the LG manual where the code is listed. If your code is not here, check the full list of LG WashTower codes.

CodeWhat it meansWhat you can doLG source
9A5Gas dryer not heating — no temperature riseMake sure the gas valve behind the dryer is on. Then igniter, flame sensor or gas valve coils.LG service manual (WSEX200HNA), p. 62
d80Exhaust duct about 80% restrictedClean the lint filter, the duct behind the dryer and the vent to the outside hood. The number is roughly the percentage of airflow blocked.LG service manual (WSEX200HNA), p. 71
d80Dryer exhaust 80–95% restrictedClean the vent behind the tower and the full run outside. Do not keep using it at d90/d95.LG service manual (WSEX200HNA), p. 71
d90Exhaust duct about 90% restrictedStop using the dryer until the vent is cleaned. Severe restriction is a fire hazard.LG service manual (WSEX200HNA), p. 72
d90Dryer exhaust 80–95% restrictedClean the vent behind the tower and the full run outside. Do not keep using it at d90/d95.LG service manual (WSEX200HNA), p. 72
d95Exhaust duct about 95% restrictedDo not use the dryer. Clean or repair the vent; check for crushed flex duct behind the dryer and a stuck outside flap.LG service manual (WSEX200HNA), p. 72
d95Dryer exhaust 80–95% restrictedClean the vent behind the tower and the full run outside. Do not keep using it at d90/d95.LG service manual (WSEX200HNA), p. 72
dEDoor not closed — door switch openClose the door firmly; if it persists the door switch has failed.LG service manual (WSEX200HNA), p. 27
dEDoor open error — the board does not see a closed door switchClose the door firmly; remove clothing caught in the gasket; check for a warped or misaligned door. Repeated dE means the door lock assembly or wiring.LG service manual (WSEX200HNA), p. 27
dEDoor open error — the board does not see a closed door switchClose the door firmly; remove clothing caught in the gasket; check for a warped or misaligned door. Repeated dE means the door lock assembly or wiring.LG service manual (WSEX200HNA), p. 27
dE1Door open — interlock switch not detected closedDoor lock assembly or its wiring; call if closing firmly does not fix it.LG owner's manual (WSEX200H*A), p. 81
dE1Door open — interlock switch not detected closedDoor lock assembly or its wiring; call if closing firmly does not fix it.LG owner's manual (WSEX200H*A), p. 81
dE4Door sensor malfunction inside the lock assemblyReplace the door lock assembly.LG owner's manual (WSEX200H*A), p. 81
dE4Door sensor malfunction inside the lock assemblyReplace the door lock assembly.LG owner's manual (WSEX200H*A), p. 81
E5Steam pump error (test mode)Pump or harness; call for repair.LG service manual (WSEX200HNA), p. 31
E5Steam pump error (test mode)Pump or harness; call for repair.LG service manual (WSEX200HNA), p. 31
EEEEPROM (control memory) errorMain board replacement.LG service manual (WSEX200HNA), p. 33
EEEEPROM (control memory) errorIf EE appears in test mode at the first press of Start, the main board needs replacing.LG service manual (WSEX200HNA), p. 33
EEEEPROM (control memory) errorIf EE appears in test mode at the first press of Start, the main board needs replacing.LG service manual (WSEX200HNA), p. 33
FEOverfill — water level too highUnplug immediately if water keeps coming in. Usually a water inlet valve stuck open; oversudsing can also trigger it. Call for repair.LG owner's manual (WSEX200H*A), p. 81
FEOverfill — water level too highUnplug immediately if water keeps coming in. Usually a water inlet valve stuck open; oversudsing can also trigger it. Call for repair.LG owner's manual (WSEX200H*A), p. 81
FFFreeze failure — water froze in the pump or hosesRare in Las Vegas; thaw with warm water in the drum and let it drain.LG owner's manual (WSEX200H*A), p. 81
FFFreeze failure — water froze in the pump or hosesRare in Las Vegas; thaw with warm water in the drum and let it drain.LG owner's manual (WSEX200H*A), p. 81
gASGas dryer not heating — no temperature riseMake sure the gas valve behind the dryer is on. Then igniter, flame sensor or gas valve coils.LG service manual (WSEX200HNA), p. 35
gASGas dryer not heatingCheck the gas valve; igniter, flame sensor or valve coils.LG service manual (WSEX200HNA), p. 35
HSHumidity sensor error — or Flow Sense test run while the dryer was still warm meaning varies by modelRun the installation check / Flow Sense test only when the dryer is cold. If HS returns cold, the sensor needs service.LG service manual (WSEX200HNA), p. 62
HSHumidity sensor error — or Flow Sense test run while the dryer was still warm meaning varies by modelRun the installation check / Flow Sense test only when the dryer is cold. If HS returns cold, the sensor needs service.LG service manual (WSEX200HNA), p. 62
IEInlet error — not enough water enteredOpen both faucets fully, check hoses for kinks, clean the inlet screens. Household pressure must be at least 20 psi. If water is on, the inlet valve or pressure sensor is suspect.LG owner's manual (WSEX200H*A), p. 75
IEInlet error — not enough water enteredOpen both faucets fully, check hoses for kinks, clean the inlet screens. Household pressure must be at least 20 psi. If water is on, the inlet valve or pressure sensor is suspect.LG owner's manual (WSEX200H*A), p. 75
LELocked motor — the motor cannot turnCheck that the drum turns freely by hand (power off). On LG direct-drive washers the usual fault is the rotor position (hall) sensor, then the stator or wiring; a foreign object between tubs is possible. Call for repair.LG service manual (WSEX200HNA), p. 33
LELocked motor — the motor cannot turnCheck that the drum turns freely by hand (power off). On LG direct-drive washers the usual fault is the rotor position (hall) sensor, then the stator or wiring; a foreign object between tubs is possible. Call for repair.LG service manual (WSEX200HNA), p. 33
LE2Drum motor low current (condensing) or compressor error (heat pump) meaning varies by modelClean the lint filter; then call.LG owner's manual (WSEX200H*A), p. 28
LE2Combo: compressor not running / drying fan lockedCall for repair.LG owner's manual (WSEX200H*A), p. 28
LE2Combo: compressor not running / drying fan locked meaning varies by modelCall for repair.LG owner's manual (WSEX200H*A), p. 28
nCWi-Fi / NFC module messages in test modeDrying is not affected.LG service manual (WSEX200HNA), p. 35
nCModem, Wi-Fi or NFC module messages (test mode only)Router or module issue; washing is not affected.LG service manual (WSEX200HNA), p. 35
nCModem, Wi-Fi or NFC module messages (test mode only)Router or module issue; washing is not affected.LG service manual (WSEX200HNA), p. 35
nEWi-Fi / NFC module messages in test modeDrying is not affected.LG service manual (WSEX200HNA), p. 20
nEModem, Wi-Fi or NFC module messages (test mode only)Router or module issue; washing is not affected.LG service manual (WSEX200HNA), p. 20
nEModem, Wi-Fi or NFC module messages (test mode only)Router or module issue; washing is not affected.LG service manual (WSEX200HNA), p. 20
nPSupply voltage not correct or power was interruptedMake sure the breaker is fully on (electric dryers use a double 240 V breaker) and the plug is seated. If the code returns, have an electrician check the outlet.LG service manual (WSEX200HNA), p. 52
nPSupply voltage not correct or power was interruptedMake sure the breaker is fully on (electric dryers use a double 240 V breaker) and the plug is seated. If the code returns, have an electrician check the outlet.LG service manual (WSEX200HNA), p. 52
OEDrain pump error — condensate water not droppingCheck the drain hose for kinks; clean lint from the pump.LG owner's manual (WSEX200H*A), p. 81
OEDrain error — water did not drain in timeClean the drain pump filter (front load: bottom-front access door). Check the drain hose for kinks and make sure its end is no higher than 96 inches. If the pump hums but does not drain, or is silent, the drain pump needs replacing.LG owner's manual (WSEX200H*A), p. 81
OEDrain error — water did not drain in timeClean the drain pump filter (front load: bottom-front access door). Check the drain hose for kinks and make sure its end is no higher than 96 inches. If the pump hums but does not drain, or is silent, the drain pump needs replacing.LG owner's manual (WSEX200H*A), p. 81
PEPressure (water level) sensor errorSensor, its hose (a pin-hole leak) or harness. Running Tub Clean can help if suds caused it; otherwise call.LG service manual (WSEX200HNA), p. 33
PEPressure (water level) sensor errorSensor, its hose (a pin-hole leak) or harness. Running Tub Clean can help if suds caused it; otherwise call.LG service manual (WSEX200HNA), p. 33
PFSupply voltage not correct or power was interruptedMake sure the breaker is fully on (electric dryers use a double 240 V breaker) and the plug is seated. If the code returns, have an electrician check the outlet.LG service manual (WSEX200HNA), p. 34
PFPower failure during a cycleNot a part failure. Press Power and restart. Frequent PF can mean a loose outlet connection.LG service manual (WSEX200HNA), p. 34
PFPower failure during a cycleNot a part failure. Press Power and restart. Frequent PF can mean a loose outlet connection.LG service manual (WSEX200HNA), p. 34
PSSupply voltage not correct or power was interruptedMake sure the breaker is fully on (electric dryers use a double 240 V breaker) and the plug is seated. If the code returns, have an electrician check the outlet.LG service manual (WSEX200HNA), p. 35
PSSupply voltage not correctMake sure the washer is plugged straight into its own standard 120 V outlet (no extension cord) and the breaker is on. If the code returns, have an electrician check the outlet.LG service manual (WSEX200HNA), p. 35
PSSupply voltage not correctMake sure the washer is plugged straight into its own standard 120 V outlet (no extension cord) and the breaker is on. If the code returns, have an electrician check the outlet.LG service manual (WSEX200HNA), p. 35
tEThermistor (water temperature sensor) errorSensor or harness out of range. Call for repair.LG service manual (WSEX200HNA), p. 21
tEThermistor (water temperature sensor) errorSensor or harness out of range. Call for repair.LG service manual (WSEX200HNA), p. 21
tE1Thermistor error — open or shorted sensor, or large difference between real and sensed temperatureThermistor or harness; call for repair.LG service manual (WSEX200HNA), p. 25
tE1Heat pump WashCombo thermistor errors (duct, compressor inlet, evaporator)Call for repair.LG service manual (WSEX200HNA), p. 25
tE1Heat pump WashCombo thermistor errors (duct, compressor inlet, evaporator)Call for repair.LG service manual (WSEX200HNA), p. 25
tE2Thermistor out of range (meaning differs on heat pump models) meaning varies by modelVery cold air from a long vent can trigger it on standard models; otherwise a sensor fault.LG service manual (WSEX200HNA), p. 25
tE2Heat pump WashCombo thermistor errors (duct, compressor inlet, evaporator)Call for repair.LG service manual (WSEX200HNA), p. 25
tE2Heat pump WashCombo thermistor errors (duct, compressor inlet, evaporator)Call for repair.LG service manual (WSEX200HNA), p. 25
tE4Steam generator thermistor errorCall for repair.LG service manual (WSEX200HNA), p. 35
tE4Heat pump WashCombo thermistor errors (duct, compressor inlet, evaporator)Call for repair.LG service manual (WSEX200HNA), p. 35
tE4Heat pump WashCombo thermistor errors (duct, compressor inlet, evaporator)Call for repair.LG service manual (WSEX200HNA), p. 35
tE7Heat pump dryer thermistor errors (compressor inlet / outlet, evaporator inlet)Call for repair.LG owner's manual (WSEX200H*A), p. 88
tE7Heat pump dryer thermistor errors (compressor inlet / outlet, evaporator inlet)Call for repair.LG owner's manual (WSEX200H*A), p. 88
CLControl (child) lock is onPress and hold the Child Lock button (often shared with another button) for 3 seconds.LG owner's manual (WSEX200H*A), p. 81
CLControl (child) lock is onPress and hold the Child Lock button (often shared with another button) for 3 seconds.LG owner's manual (WSEX200H*A), p. 81
nFWi-Fi / NFC module messages in test modeDrying is not affected.LG service manual (WSEX200HNA), p. 20
nFModem, Wi-Fi or NFC module messages (test mode only)Router or module issue; washing is not affected.LG service manual (WSEX200HNA), p. 20
nFModem, Wi-Fi or NFC module messages (test mode only)Router or module issue; washing is not affected.LG service manual (WSEX200HNA), p. 20

Locks, resets and settings

From the LG owner's manual for this series. Button names are printed on the control panel; on some panels the function is printed under a button that has another main use.

  • Child Lock / Control Lock. To turn the lock on or off: press and hold Control Lock for 3 seconds. (LG owner's manual (WSEX200H*A), p. 80)

When to call a technician

Codes that point to a sensor, motor, fan, board, heater or the sealed system need testing with meters and LG test mode. Typical LG WashTower repairs in Las Vegas cost $200–$580 including the $75 service call — see repair prices and LG washtower repair.

Step-by-step guides for common problems:

Sources

  • LG service manual for WSEX200HNA (© 2019-2021) — 125 pages, LG P/No MFL68588942
  • LG owner's manual for WSEX200H*A, WSGX201H*A, WSEX200HNA (© 2020-2021) — 100 pages, LG P/No MFL71728915
  • LG owner's manual for WSEX200HNA, WSGX201HNA (© 2020) — 132 pages, LG P/No MFL71728914

Facts on this page are taken from LG's own documentation and LG's technician error-code reference; explanations are written by our technicians. LG manuals are copyrighted by LG Electronics and are not reproduced here. LG Appliances Repair Service is independent and not affiliated with LG.

LG WSEX200HNA questions

How do I turn off the control lock on an LG WSEX200HNA?

Press and hold control lock for 3 seconds. (LG LG owner's manual (WSEX200H*A), p. 80.)

What does OE mean on an LG WSEX200HNA?

Drain error — water did not drain in time. Clean the drain pump filter (front load: bottom-front access door). Check the drain hose for kinks and make sure its end is no higher than 96 inches. If the pump hums but does not drain, or is silent, the drain pump needs replacing.

What does IE mean on an LG WSEX200HNA?

Inlet error — not enough water entered. Open both faucets fully, check hoses for kinks, clean the inlet screens. Household pressure must be at least 20 psi. If water is on, the inlet valve or pressure sensor is suspect.

Do you repair the LG WSEX200HNA in Las Vegas and Henderson?

Yes. LG Appliances Repair Service repairs LG WashTowers, including the WSEX200 series, in homes across Las Vegas and Henderson. The $75 service call is credited toward the repair.

Online booking

Book LG WSEX200HNA repair

Tell us what the appliance is doing and when you are home. We call back to confirm a time — usually the same day during business hours. The $75 service call is credited toward your repair.

  • EPA 608 certified
  • Fully insured
  • $75 service call, credited to repair
  • 90-day labor · 1-yr parts warranty

Request LG repair

Prefer to talk? Call (702) 707-5107. We confirm online requests during business hours.

LG appliances only · Las Vegas & Henderson

Your LG appliance, fixed by technicians who work on LG every day.

$75 service call, credited toward the repair. Written quote before any work. EPA 608 certified, fully insured. 90-day labor warranty, 1-year warranty on parts.

Call now Book online